Flemmig Dennis
2014-10-21 05:26:44 UTC
Hi Joshua,
I think you are missing this config :
N Chassis(su)->set igmp enable 5
N Chassis(su)->set igmp enable 10
N Chassis(su)->set igmp enable 20
N Chassis(su)->set igmp query-enable 10
N Chassis(su)->set igmp query-enable 5 (If the computers should be able to receive the stream as well)
This enables IGMP on the VLANs and IGMP queries on 10 & 5 in switch mode.
If it is still not working you may need to have a look at the IGMP snooping configuration on the 3750.
In the N-Series Config Guide, there is a pretty good example of a Multicast configuration.
Kind Regards
Dennis
Mit freundlichen Grüßen / Best regards
Dennis Flemmig (Dipl.-Ing.)
Senior System Engineer
[cid:***@01CFED00.5DC92540]
CANCOM DIDAS GmbH
Elisabeth-Selbert-Str. 4a
40764 Langenfeld
Deutschland
Phone +49 2173 5966-470
Fax +49 2173 5966-610
Mobile +49 172 5219729
***@cancom.de<mailto:***@cancom.de>
www.cancom-didas.de<http://www.cancom-didas.de/>
CANCOM DIDAS GmbH
Sitz der Gesellschaft: Langenfeld
AG Düsseldorf HRB 63231, USt-Id Nr.: DE811548338
Geschäftsführer: Dirk Kiefer, Thorsten Eska
Diese E-Mail und alle mitgesendeten Dateien sind vertraulich und ausschließlich für den Gebrauch durch den Empfänger bestimmt!
This e-mail and any files transmitted with it are confidential intended solely for the use of the addressee!
Von: ***@westernmutual.com [mailto:***@westernmutual.com]
Gesendet: Dienstag, 21. Oktober 2014 01:22
An: Enterasys Customer Mailing List
Betreff: [enterasys] Multicast config
I'm trying to configure PIM-SM on a Enterasys N7 so Multicast traffic can route from a server hanging off the N7 to a Vlan Trunk going to a Cisco 3750 where some phones are located.
I was just wondering if I could have another pair of eyes look at my config because it's not currently working. This is what I have, please tell me if I'm missing anything.
interface vlan 5 *** this is the vlan our computers sit on. It's here because it's in the trunk going to the 3750
ip address 10.205.1.1 255.255.248.0
ip pim sparse-mode
interface vlan 10 *** this is the vlan our phones are on
ip address 10.210.1.1 255.255.248.0
ip pim sparse-mode
interface vlan 20 *** this is where the server is hanging off
ip address 10.220.1.1 255.255.248.0
ip pim sparse-mode
ip pim bsr-candidate vlan 5
ip pim rp-candidate 10.205.1.1 224.0.0.0 224.0.0.0
Joshua Sanders
Asst. Vice President - Systems Operations
Western Mutual Insurance Group
***@westernmutual.com<mailto:***@westernmutual.com>
* --To unsubscribe from enterasys, send email to ***@unc.edu<mailto:***@unc.edu> with the body: unsubscribe enterasys ***@cancom.de<mailto:***@cancom.de>
---
To unsubscribe from enterasys, send email to ***@unc.edu with the body: unsubscribe enterasys gneu-***@gmane.org
I think you are missing this config :
N Chassis(su)->set igmp enable 5
N Chassis(su)->set igmp enable 10
N Chassis(su)->set igmp enable 20
N Chassis(su)->set igmp query-enable 10
N Chassis(su)->set igmp query-enable 5 (If the computers should be able to receive the stream as well)
This enables IGMP on the VLANs and IGMP queries on 10 & 5 in switch mode.
If it is still not working you may need to have a look at the IGMP snooping configuration on the 3750.
In the N-Series Config Guide, there is a pretty good example of a Multicast configuration.
Kind Regards
Dennis
Mit freundlichen Grüßen / Best regards
Dennis Flemmig (Dipl.-Ing.)
Senior System Engineer
[cid:***@01CFED00.5DC92540]
CANCOM DIDAS GmbH
Elisabeth-Selbert-Str. 4a
40764 Langenfeld
Deutschland
Phone +49 2173 5966-470
Fax +49 2173 5966-610
Mobile +49 172 5219729
***@cancom.de<mailto:***@cancom.de>
www.cancom-didas.de<http://www.cancom-didas.de/>
CANCOM DIDAS GmbH
Sitz der Gesellschaft: Langenfeld
AG Düsseldorf HRB 63231, USt-Id Nr.: DE811548338
Geschäftsführer: Dirk Kiefer, Thorsten Eska
Diese E-Mail und alle mitgesendeten Dateien sind vertraulich und ausschließlich für den Gebrauch durch den Empfänger bestimmt!
This e-mail and any files transmitted with it are confidential intended solely for the use of the addressee!
Von: ***@westernmutual.com [mailto:***@westernmutual.com]
Gesendet: Dienstag, 21. Oktober 2014 01:22
An: Enterasys Customer Mailing List
Betreff: [enterasys] Multicast config
I'm trying to configure PIM-SM on a Enterasys N7 so Multicast traffic can route from a server hanging off the N7 to a Vlan Trunk going to a Cisco 3750 where some phones are located.
I was just wondering if I could have another pair of eyes look at my config because it's not currently working. This is what I have, please tell me if I'm missing anything.
interface vlan 5 *** this is the vlan our computers sit on. It's here because it's in the trunk going to the 3750
ip address 10.205.1.1 255.255.248.0
ip pim sparse-mode
interface vlan 10 *** this is the vlan our phones are on
ip address 10.210.1.1 255.255.248.0
ip pim sparse-mode
interface vlan 20 *** this is where the server is hanging off
ip address 10.220.1.1 255.255.248.0
ip pim sparse-mode
ip pim bsr-candidate vlan 5
ip pim rp-candidate 10.205.1.1 224.0.0.0 224.0.0.0
Joshua Sanders
Asst. Vice President - Systems Operations
Western Mutual Insurance Group
***@westernmutual.com<mailto:***@westernmutual.com>
* --To unsubscribe from enterasys, send email to ***@unc.edu<mailto:***@unc.edu> with the body: unsubscribe enterasys ***@cancom.de<mailto:***@cancom.de>
---
To unsubscribe from enterasys, send email to ***@unc.edu with the body: unsubscribe enterasys gneu-***@gmane.org